收藏本站
Si4320
RESET MODES
The chip will enter into reset mode if any of the following conditions are met:
? Power-on reset: During a power up sequence until the V dd has reached the correct level and stabilized
? Power glitch reset: Transients present on the V dd line
? Software reset: Special control command received by the chip
Power-on reset
After power up the supply voltage starts to rise from 0V. The reset block has an internal ramping voltage reference (reset-ramp signal), which
is rising at 100mV/ms (typical) rate. The chip remains in reset state while the voltage difference between the actual V dd and the internal
reset-ramp signal is higher than the reset threshold voltage, which is 600 mV (typical). As long as the V dd voltage is less than 1.6V (typical)
the chip stays in reset mode regardless the voltage difference between the V dd and the internal ramp signal.
The reset event can last up to 150ms supposing that the V dd reaches 90% its final value within 1ms. During this period the chip does not
accept control commands via the serial control interface.
Power-on reset example:
Power glitch reset
The internal reset block has two basic mode of operation: normal and sensitive reset. The default mode is sensitive, which can be changed
by the appropriate control command (see Related control commands at the end of this section). In normal mode the power glitch detection
circuit is disabled.
There can be spikes or glitches on the V dd line if the supply filtering is not satisfactory or the internal resistance of the power supply is too
high. In such cases if the sensitive reset is enabled an (unwanted) reset will be generated if the positive going edge of the V dd has a rising
rate greater than 100mV/ms and the voltage difference between the internal ramp signal and the V dd reaches the reset threshold voltage
(600 mV). Typical case when the battery is weak and due to its increased internal resistance a sudden decrease of the current consumption
(for example turning off the power amplifier) might lead to an increase in supply voltage. If for some reason the sensitive reset cannot be
disabled step-by-step decrease of the current consumption (by turning off the different stages one by one) can help to avoid this problem.
Any negative change in the supply voltage will not cause reset event unless the V dd level reaches the reset threshold voltage (250mV in
normal mode, 1.6V in sensitive reset mode).
If the sensitive mode is disabled and the power supply turned off the V dd must drop below 250mV in order to trigger a power-on reset event
when the supply voltage is turned back on. If the decoupling capacitors keep their charges for a long time it could happen that no reset will
be generated upon power-up because the power glitch detector circuit is disabled.
Note that the reset event reinitializes the internal registers, so the sensitive mode will be enabled again.
24
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SI4322-A0-FT IC RX FSK UNI 868/915MHZ 16TSSOP
SI4324DY-T1-GE3 MOSFET N-CH D-S 30V 8-SOIC
SI4330-B1-FM IC RCVR ISM 960MHZ 3.6V 20-QFN
SI4354DY-T1-GE3 MOSFET N-CH D-S 30V 8-SOIC
SI4355-B1A-FM IC EZRADIO FM RECEIVER SI4355
SI4388DY-T1-GE3 MOSFET DUAL N-CH 30V 8-SOIC
SI4390DY-T1-GE3 MOSFET N-CH 30V 8.5A 8SOIC
SI4396DY-T1-GE3 MOSFET N-CH D-S 30V 8-SOIC
相关代理商/技术参数
SI4320-J1-FTR 功能描述:射频接收器 Receiver (EZRadio) RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
Si4322-A0-FT 功能描述:射频接收器 Receivers - IA4322 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4322-A0-FTR 功能描述:射频接收器 Receiver (EZRadio) RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
Si4322-A1-FT 功能描述:射频接收器 RECEIVER EZRadio UNIVRSL ISM BAND FSK RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4322DY-T1-E3 功能描述:MOSFET 30V 18A 5.4W 8.5mohm @ 10V RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4322DY-T1-GE3 功能描述:MOSFET 30V 18A 5.4W 8.5mohm @ 10V RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4324DY-T1-E3 功能描述:MOSFET 30V 36A 7.8W RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4324DY-T1-GE3 功能描述:MOSFET 30V 36A 7.8W 3.2mohm @ 10V RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube